Tools

Replacement threaded cap for Abbey Hanger Alligment Gauge Tool.

Replacement shaft for Micro Bearing Press - 1/4" shaft diameter - 12" length

The soft face on the Titanium Hammer is destined to be gouged, get worn down, or even melt (if you leave it near heat). Replacement soft face for Abbey Titanium Hammer.

Replacement pins, these are original equipment chain pins for our chain tool, they also work as an alternate to the Campagnolo UT-CN300 11spd chain tool, Shimano CN-34 and CN-32 Sold in pairs.

Replacement feeler gauge for the Abbey Hanger Alligment Gauge Tool.

For use with 1/4" Micro Bearing Press Shaft

The soft face on the Shop Hammer is destined to be gouged, get worn down, or even melt (if you leave it near heat). Replacement soft face for Abbey Shop Hammer.

For use with 1/2" Micro Bearing Press Shaft

Replacement 6/8mm Hex bit for both the Abbey BBQ Wood Handled Pedal Wrench and the Team Issue Pedal Wrench.

1/8" mid plate, needed to use the Decade chain tool with wide 1/8" track and single speed chains.

This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.

This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.

This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.

This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.

This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.

This tool makes dust wiper installation an easy task. The Fork Seal Press is built with modern tight fitting fork seals in mind. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time.

The lever setter is a unique tool that works in conjunction with our HAG (or other hanger allignment tool) to set brake and shifter levers at the same height from side to side. The tool temporarily replaces the headset top cap and allows you to thread a hanger alignment tool into the lever setter. Use the HAG indicator to set levers the same from one side of the bar to the other. Once you're satisfied with your lever placement simply remove the tool and replace your headset top cap and go ride. Compatibility: Requires a star nut or compression plug with a M6x1 thread. Works with road and mountain shifters and brake levers. Compatible with most hanger alignment tools on the market. Recommendations: It's advised to use a spacer on top of the stem to help align the lever setter with the steer tube. This will reduce the impact the quality of the cut on the steer tube has on the function of the tool. The supplied threaded stud can be replaced with a longer one if needed.

The Shimano Crank Tool (SCT for short) is specifically built to service the chainring lockring on Shimano single ring cranksets for 12 speed drivetrains. It features a large hex that can be used with a 1.5" or 38mm wrench or locked into a vise. The clearance hole is kept to a minimum to keep the tool engaged on the low profile lockring, minimizing the chance of damaging the tool or parts. Compatibility: - Chain ring lockrings on Shimano 12spd mountain crank sets. - XT and Ultegra bottom brackets

The Abbey Bike Tools 4-way precision multi-tool is the perfect choice to carry with you while on a ride. We designed this beautiful green anodized tool to fit into a compact saddle bag, riding wallet, or tuck into a jersey pocket. Everybody makes a multi-tool and there's a little bit of everything on the market, so what's different about ours? All of the little things that add up to one nice little tool. A multi tool is only as good as it's tool engagement so that's where we started. If you're familiar with other Abbey tools you've no doubt noticed that they fit tighter than anything else out there and this one is no different. We use precision stainless steel bits that fit like a glove into the bolts on your modern bike. They wont strip out fasteners like the cheap offshore made tools that are so common in the bike world. They also won't rust into a ugly brown color after a season in a saddle bag. The next part of the multi-tool is the chassis, for this we used our favorite US drawn aluminum alloy and built a 4 position frame to hold the bits. At first glance the tool looks like it might be cumbersome but once you get it in your hand you realize how simple and effective the ergonomics of the tool are. Offering good leverage for all of the small fasteners on your bike, be it the precision adjustment of limit screws or adjusting the handle bars because you had one beer too many when you bolted them down late last night. Available in 5 pre-configured options or fully customizable to fit whatever mix of fasteners your bike requires. We suggest buying a tool for each of your bikes and leaving the tool stored away until needed. These little multi-tools are the result of a collaboration with fellow Bend OR residents, Argonaut Cycles and is the only American manufactured multi-tool for the bicycle market.

The Abbey Bike Tools 4-way precision multi-tool is the perfect choice to carry with you while on a ride. We designed this beautiful green anodized tool to fit into a compact saddle bag, riding wallet, or tuck into a jersey pocket. Everybody makes a multi-tool and there's a little bit of everything on the market, so what's different about ours? All of the little things that add up to one nice little tool. A multi tool is only as good as it's tool engagement so that's where we started. If you're familiar with other Abbey tools you've no doubt noticed that they fit tighter than anything else out there and this one is no different. We use precision stainless steel bits that fit like a glove into the bolts on your modern bike. They wont strip out fasteners like the cheap offshore made tools that are so common in the bike world. They also won't rust into a ugly brown color after a season in a saddle bag. The next part of the multi-tool is the chassis, for this we used our favorite US drawn aluminum alloy and built a 4 position frame to hold the bits. At first glance the tool looks like it might be cumbersome but once you get it in your hand you realize how simple and effective the ergonomics of the tool are. Offering good leverage for all of the small fasteners on your bike, be it the precision adjustment of limit screws or adjusting the handle bars because you had one beer too many when you bolted them down late last night. Available in 5 pre-configured options or fully customizable to fit whatever mix of fasteners your bike requires. We suggest buying a tool for each of your bikes and leaving the tool stored away until needed. These little multi-tools are the result of a collaboration with fellow Bend OR residents, Argonaut Cycles and is the only American manufactured multi-tool for the bicycle market.

The Abbey Bike Tools 4-way precision multi-tool is the perfect choice to carry with you while on a ride. We designed this beautiful green anodized tool to fit into a compact saddle bag, riding wallet, or tuck into a jersey pocket. Everybody makes a multi-tool and there's a little bit of everything on the market, so what's different about ours? All of the little things that add up to one nice little tool. A multi tool is only as good as it's tool engagement so that's where we started. If you're familiar with other Abbey tools you've no doubt noticed that they fit tighter than anything else out there and this one is no different. We use precision stainless steel bits that fit like a glove into the bolts on your modern bike. They wont strip out fasteners like the cheap offshore made tools that are so common in the bike world. They also won't rust into a ugly brown color after a season in a saddle bag. The next part of the multi-tool is the chassis, for this we used our favorite US drawn aluminum alloy and built a 4 position frame to hold the bits. At first glance the tool looks like it might be cumbersome but once you get it in your hand you realize how simple and effective the ergonomics of the tool are. Offering good leverage for all of the small fasteners on your bike, be it the precision adjustment of limit screws or adjusting the handle bars because you had one beer too many when you bolted them down late last night. Available in 5 pre-configured options or fully customizable to fit whatever mix of fasteners your bike requires. We suggest buying a tool for each of your bikes and leaving the tool stored away until needed. These little multi-tools are the result of a collaboration with fellow Bend OR residents, Argonaut Cycles and is the only American manufactured multi-tool for the bicycle market.

The Abbey Bike Tools 4-way precision multi-tool is the perfect choice to carry with you while on a ride. We designed this beautiful green anodized tool to fit into a compact saddle bag, riding wallet, or tuck into a jersey pocket.

The Abbey Bike Tools 4-way precision multi-tool is the perfect choice to carry with you while on a ride. We designed this beautiful green anodized tool to fit into a compact saddle bag, riding wallet, or tuck into a jersey pocket. Everybody makes a multi-tool and there's a little bit of everything on the market, so what's different about ours? All of the little things that add up to one nice little tool. A multi tool is only as good as it's tool engagement so that's where we started. If you're familiar with other Abbey tools you've no doubt noticed that they fit tighter than anything else out there and this one is no different. We use precision stainless steel bits that fit like a glove into the bolts on your modern bike. They wont strip out fasteners like the cheap offshore made tools that are so common in the bike world. They also won't rust into a ugly brown color after a season in a saddle bag. The next part of the multi-tool is the chassis, for this we used our favorite US drawn aluminum alloy and built a 4 position frame to hold the bits. At first glance the tool looks like it might be cumbersome but once you get it in your hand you realize how simple and effective the ergonomics of the tool are. Offering good leverage for all of the small fasteners on your bike, be it the precision adjustment of limit screws or adjusting the handle bars because you had one beer too many when you bolted them down late last night. Available in 5 pre-configured options or fully customizable to fit whatever mix of fasteners your bike requires. We suggest buying a tool for each of your bikes and leaving the tool stored away until needed. These little multi-tools are the result of a collaboration with fellow Bend OR residents, Argonaut Cycles and is the only American manufactured multi-tool for the bicycle market.

We listened to your requests and created a socket style Crombie tool that is compatible with ratchets and torque wrenches. The Socket Crombie has our signature finger spline at the top along with a 3/8" square drive for using your favorite ratchet or torque wrench. The tool is plenty deep to hide a quick release and still get full engagement on the lock ring. Compatible with all Campagnolo cassettes.

The Charger 2 wrench is designed for use on the lower seal head of Charger 2 and Charger LT dampers. This series of wrenches comes as a result of our collaboration with RockShox to develop a series of tools specifically for their suspension components. Built to hold the thin aluminum parts of the dampers to avoid damage. These wrenches are built with the same tool grade aluminum to tight tolerances to give you years of trouble free use. They will not damage or mar the sensitive parts inside your suspension fork when used with care, keeping you and your customers happy. They also feature a 3/8" square drive in the middle to use with your favorite torque wrench during reassembly.

The Reverb is an advanced and complicated component and service becomes a breeze with this speciality wrench. Designed for use on the inner seal head and upper collet of both 30.9 and 31.6 millimeter version of the Reverb dropper post. This series of wrenches comes as a result of our collaboration with RockShox to develop a series of tools specifically for their suspension components. Built to hold the thin aluminum parts of the dampers to avoid damage. These wrenches are built with the same tool grade aluminum to tight tolerances to give you years of trouble free use. They will not damage or mar the sensitive parts inside your seastpost when used with care, keeping you and your customers happy. They also feature a 3/8" square drive in the middle to use with your favorite torque wrench during reassembly.

Many athletes are fortunate enough to be able to ride nearly anything. For those that are sensitive to bike fit though, replicating fit to a new bike or confirming fit after travel can be a challenge involving lots of trial and error. This set of tools allows accurate and repeatable measurements for saddle height, angle and setback. The accuracy and repeatable measurements also serve as a base to make adjustments to fit. -The magnetic saddle height bullets ensure you get an accurate center at the BB by locating in the crank arm fixing bolt or the crank arm preload cap of Shimano caps. This allows you to focus on the smart end of the tape measure at the saddle plate. -Two reference marks on the saddle plate means you can pull a measurement to the exact same spot relative to the nose of the saddle every time. This gives you accuracy down to a single millimeter. -The front of the saddle plate is engraved with a ruler, to allow you to calculate saddle setback at the saddle. This allows you to drop the plumb bob off the side of the bike and clear all of the bottle cages. -The wide plate has ample room to mount a level, protractor or smart phone for adjusting the angle of the saddle. This is particularly helpful for non traditional saddles like SMP and Adamo.

Brake pad spreader tool for Avid Elixir brakes.

SRAM Bleed Kit for maintaining SRAM disc brakes. Includes 2 syringes/fittings, bleed blocks, Torx tool, Crow's foot, and Bleeding Edge Fitting. - For SRAM X0/ XX/ Guide/Level/Code/HydroR brakes - Improved sealing and durability - New rotating metal hose fittings - High volume hose with clamp - Longer lasting - Must-have for all mechanics - NOT compatible with RockShox fork bleed kit - Brake fluid sold separately

This item contains 10 replacement plugs for the Blackburn Plugger Tubeless tool (sold separately), a one-shot tire plugging system for tubeless tires. It deploys in seconds to give a permanent fix for your flat.

Essential tool in mini size An essential tool for modern riders with tubeless tires, road or dirt. The Mini Plugger is a quick, one-shot tire-plugging system with a tiny profile to easily store and access in pockets, bags, or packs. A self-contained rescue tool when and where you need it most. - QUICK FIX - No need to remove the tire, just quickly access your Plugger tool, repair the tire, inflate, and go! - 5 PLUGS - Includes 5 tire plugs, internally stored - LIFETIME WARRANTY

Essential tools in mini size The Mini-Switch is an essential tool kit with a slim profile to easily store and access in pockets, bags, and packs. Outfitted with a technical bit offering appropriate for most performance-oriented bikes, in a tool bit platform that we are all used to using at home. - 6 TOOLS - Top six tools for most modern bikes. 3mm, 4mm, 5mm, 6mm, Allen bits and T25, T30 Torx bits - HEX BITS - Easy to switch out tools. A durable, time-proven, six-sided bit design - LIGHTWEIGHT - Extremely light and compact tool set that's unnoticeable while riding - LIFETIME WARRANTY

8 functions—we've gone out of our way to pack this tool with as many useful functions as humanly possible. The selection, length, and placement of each tool has been carefully thought out so that you have the right tool and can easily use it. - 110 grams

The only wrap that's better than this is an actual burrito. Blackburn's Outpost Wrap Bag is a clever compartmentalized tool wrap that fits all your essentials for a big day. And if you're just heading round the corner, just zip off the smaller section and carry only what you need. - Straps can mount to frame in multiple locations for a secure fit - Several mesh and slip pockets, room for everything - Weight: 80g / 2.8oz

13 functions—we've gone out of our way to pack this tool with as many useful functions as humanly possible. The selection, length, and placement of each tool has been carefully thought out so that you have the right tool and can easily use it. - 13 functions - 145 grams

Those guys who said "Tubeless tires never get punctures"? They lied. The Blackburn Plugger Tubeless Tire Repar Kit is a quick, one-shot tire plugging system for tubeless tires. It deploys in seconds to give a permanent fix for your flat. Mount it to your frame, tape it to your top tube, or strap it to your ankle like a shark knife. Just keep it close and it'll get you out of trouble. Pronto. - Stores ten plugs. - 27g tool only 47g tool with strap

The Switch Tool has evolved. We've all heard "if it ain't broke, don't fix it", but what if riders just want to fix more things? Enter the Big Switch, the larger sibling to the hit Switch tool. This new, compact, and super functional tool kit includes essentials you’ll find on the Switch including T25 and T30 torx bits, 2.5, 3, 4, 5, and 6mm allen bits, and a flathead screwdriver. The Big Switch also features an 8mm hex tool, and a chain breaker. The chain breaker handle includes size 0, 1, and 2 spoke wrenches, a disc pad spreader and a Presta valve core tool. Individual T or L handle tools let you access tight places and give you more leverage on bolts and screws. Go ahead, fix everything. - 15 functions - Includes T or L handle wrenches. - Tool bits include: T25, T30, 2.5mm, 3mm, 4mm, 5mm, 6mm, 8mm, and a flathead. - Pocket sized nylon carrying pouch includes a stash for your I.D., credit card, and cash. - 134g

Customize the Switch Wrap Bag and load it up with your favorite tools. - Compact design—despite its near-limitless functionality, the big switch ratchet tool (sold separately) fits compactly in your hand thanks to a well-thought-out modular design allowing for leverage within the confines of a portable nylon wallet. - Customizable—wrap almost anything you need and take it with you. - Features specific sleeves for an inner tube, a 20g C02 cartridge, 2 tire levers, credit cards, and cash (sold separately) - Weight: 3.52oz - Lifetime warranty

Remember that time on the trail when your brake lever reach went out of whack? Unfortunately, your multi tool couldn't get out of it's own way to turn the adjustment screw. Blackburn's Wayside Multi Tool changes all of that. - Individual Hex Keys - The most common hex keys snap on and off the tool and can be used individually to be able easily reach and properly torque any bolt head. All keys feature a ball end. - Optimized Tools - The selection, length and placement of each tool has been carefully thought out so that you have the right tool and can easily use it. - 19 functions - 200 grams / 0.44 lbs

Imagine if you could bring a tool box with all the essentials you’d need for bicycle maintenance with you on every ride. Well then, stop dreaming: the Blackburn Switch Wrap is already here. Spec’d with their Big Switch multi tool, the Switch Wrap provides you quick access to everything you’ll need to fix just about anything that could go wrong on a ride. The Wrap features specific sleeves for an inner tube, up to a 20g CO2 cartridge, and a tire lever. And, it keeps the Big Switch tools at your fingertips. When opened, the tool kit hangs from your saddle so you can grab what you need without spreading it all on the ground, so lost tools will only exist in nightmares. Minimal. Compact. Secure. Convenient. The Switch Wrap. - 15 functions - Includes T or L handle wrenches. - Tool bits include: T25, T30, 2.5mm, 3mm, 4mm, 5mm, 6mm, 8mm and a flathead. - Nylon carrying pouch features sleeves for 20g CO2 cartridge, tire lever and includes a stash for your I.D., credit card and cash. - Attaches to seat rails or to bicycle frame. - 186g

Your race mechanic on the go. Just because it's scaled down from a full-size ratchet doesn't mean it skimps on performance. The Big Switch Ratchet Tool takes the same simple necessities from the popular Switch and Big Switch and adds a convenient, ratcheting handle for even quicker, hassle-free adjustments. Extra-long 2.5 through 8mm Allen bits take care of business, along with T25 and T30 Torx, the renowned Wayside chain breaker, 0, 1, and 2 spoke wrenches, a disc-pad spreader, flathead, and a Presta valve core tool. You're covered. Fully covered. - Includes: T25, T30 Torx bits, extra-long 2.5, 3, 4, 5, 6, 8mm Allen bits, flathead screwdriver, wayside chain breaker, size 0,1, 2 spoke wrenches, disc pad spreader, Presta valve core tool

Ride essentials. Going for a ride but don’t know what to pack? No problem; we’ve got you covered. The local ride kit offers up what you need to get home; and extra carrying capacity to bring along anything else. With a seatbag, mini pump, mini tool and tire levers, this little kit, bundled in a compact package, has all the tools you need to get out there and keep going. - Blackburn's Local Seat Bag (Medium) offers extra space to pack your tube, wallet, phone, or whatever you want - Blackburn Heist 6 Multi Tool provides a quality tool to make sure your bike is adjusted properly for your ride - Blackburn's Mountain AnyValve Mini-Pump comes equipped with their popular and proven AnyValve head, which works on Presta, Schrader, and Dunlop valves. - 2x tire levers

Going for a ride but don't know what to pack? No problem, Blackburn has you covered. The new Local CO2 Ride Kit offers up what you need to get home, and extra carrying capacity to bring along anything else. - Local Small seat bag offers extra space to pack your tube, wallet, phone, or whatever you want - Wayside CO2 inflator with 16g cartridge - GRID 8 Mutli-tool provides a quality tool to make sure your bike is adjusted properly for your ride - 2x tire levers

Take greatness, add more = more greatness. The simply stellar Pro Plugger gains a few extra ingredients for surefire success, the it-makes-sense CO2’FER head combining an inflator and valve tool along with a 25g threaded CO2 and universal frame-mounting kit, mean everything’s always within reach, even on bikes with long reach. No need to scurry about rounding up odds and ends trying to beat dwindling daylight—simply grab bike, go and you’re already equipped with the Pro Plugger Combo’s on-bike tubeless repair system. - Pro plugger rubber mount, strap, core CO2 inflator and 25g threaded CO2 included - 4.64oz

Everything you need to keep your Penthouse Flat MK5 pedals feeling like new. Includes: - Small Bushing and Bearing Removal Tool - Small Bushing Press Tool - Big Bushing Press Tool - Bearing Press Tool

- Spare pin for UT-CN200 and UT-CN300

When you are installing headset cups into your bicycle frame or a crown race onto your fork, there is only one way to get the job done right. Use an appropriately-sized Cane Creek installation tool, or risk damaging your frame and/or fork. The headset cup installation tools are designed to be used with a headset press, sold separately.

Service kit for Cane Creek suspension forks.

Allows safe installation and removal of Cane Creek Double Barrel bushings.

The ultimate trail-side companion. Details - 13 high tensile steel multi-tools, including an integrated tire plug tool - Tire plugs come included with a storage case that mounts directly to the tool - The case can be used to conveniently store chain links Specs - Hex Wrenches: #2, 2.5, 3, 4, 5, 6, 8 - Length: 89mm - Screw Drivers: Phillips #1 & #2, flat #1 - Specialty Tools: Tire plug tool, tire plugs - Torx: T-10, T-25 - Warranty: Lifetime - Weight: 164g

The ultimate trailside companion. These high tensile steel multi-tools feature a precise fit and finish and side grips for a secure handhold even with gloves on. The m17 includes: Chain tool: 8/9/10 speed compatible Spoke wrench: #0, 1, 2, 3 Hex wrenches: #2, 2.5, 3, 4, 5, 6, 8 Open wrench: 8mm, 10mm Screwdrivers: Phillips #2, flat #2 Torx: t-25 Length: 89 mm Weight: 168g Warranty: Lifetime

Tubeless tire plug kit plus CO2 head. - Tire plug tool - Tire plugs - CO2 head - Storage case - Mounting bracket - 5 year warranty

The ultimate trailside companion. These high tensile steel multi-tools feature a precise fit and finish and side grips for a secure handhold even with gloves on. The m19 includes: - Chain tool: 8/9/10 speed compatible - Spoke wrench: #0, 1, 2, 3 - Hex wrenches: #2, 2.5, 3, 4, 5, 6, 8 - Open wrench: 8mm, 10mm - Screwdrivers: Phillips #1, Phillips #2, flat #2 - Torx: t-10, t-25 - Stainless steel carrying case - Length: 89 mm - Weight: 175g - Warranty: lifetime

The ultimate trail-side companion. Details - 20 high tensile steel multi-tools, including an integrated tire plug tool - Tire plugs come included with a storage case that mounts directly to the tool - The case can be used to conveniently store chain links Specs - Chain Tool: 8/9/10/11/12 speed compatible - Hex Wrenches: #2, 2.5, 3, 4, 5, 6, 8 - Length: 89mm - Open Wrench: 8mm - Screw Drivers: Phillips #1 & #2, flat #1 - Specialty Tools: Tire plug tool, tire plugs, valve core removal tool, rotor straightener - Spoke Wrench: #0, 1, 2 - Torx: T-10, T-25 - Warranty: Lifetime - Weight: 203g

Thin, light and minimalist design. - 5-year warranty - Hex wrenches : 2, 2.5, 3, 4, 5, 6, 8mm - Screwdrivers : Phillips #2, flat #2 - Torx : t-25 - 8-12 speed chain tool is incorporated into the case - Spoke wrench : #0, 1, 2 & 3 - Magnetized storage case can be used as a handle for extra leverage

Crank Brothers puts their well-known design aesthetic to the humble tire lever with the Speedier Lever. Can we call a single piece of nylon revolutionary? First off, this thing is tough. It removes and installs wire-beaded DH tires, UST tires, and brand-new road tires easily, without breaking. The genius loop protects your knuckles! It installs tires too, without pinching the tube, just flip it and use the other side. And only one lever is needed to remove even the most recalcitrant tires. Oh Speedier Lever, where have you been all my life?

The Bead Dropper tire tool significantly helps in removal and installation of CushCore tire inserts, especially the critical step of dropping the bead into the rim channel. - Rubberized ergonomic handle - Unique "thumb flange" makes it easy to apply pressure to the tire bead - Sturdy, durable plastic lever—strong enough for DH tires, yet won't scratch your rims - Lifetime warranty

- bearing tool for Vault, V18 or V14 models

DT Swiss spoke wrenches for repairing all types of DT Swiss wheels. - This professional tool is designed for precise fit and prevents rounding of nipples - Metal nipple interface contacts nipple on all four surfaces - Fits 3.25mm square nipple interface

The DT Swiss truing stand is the stand used by professionals. It is made of precision machined, polished, and anodized aluminum with hardened steel guides and mounts. - High-end quality and easy handling - Quicker wheel building - Compatible with all current bicycle wheels (12" – 29") with quick-release or thru-axle - Three precision multilink arms providing a wide range of contact points - Play-free precision gauges to measure lateral and vertical dish - Extremely stiff and solid clamping